The dedicated maintenance division for the physical AGL light fixture itself — covering every fixture type independent of where it sits on the airfield. Where Divisions 01–05 define when and why maintenance happens (preventive, corrective, predictive, condition-based, emergency), Division 06 is the technical reference for how the fixture is physically maintained: mechanically, optically, electrically, and environmentally.
Core principle: a light fixture is not considered properly maintained merely because it turns ON. Its mechanical condition, optical condition, electrical condition, environmental protection, and alignment must all remain acceptable together.
Every fixture maintenance activity in this division follows the same underlying sequence, regardless of fixture type or airfield location — and is judged against the same five conditions.
This division applies to the physical fixture regardless of application — the same mechanical, optical, electrical and environmental procedures apply wherever the fixture is installed.
A working sequence technicians can apply to any fixture, from first observation through to closed-out record.
| Step | Guiding Question |
|---|---|
| 1 · Inspect | What is physically wrong? |
| 2 · Clean | Is contamination causing the condition? |
| 3 · Assess | Is the component damaged or deteriorated? |
| 4 · Repair / Replace | Can the component be restored? |
| 5 · Align | Is the fixture correctly positioned? |
| 6 · Seal / Protect | Is the fixture protected against environmental ingress? |
| 7 · Test | Does the fixture function correctly? |
| 8 · Verify | Is the final condition acceptable? |
| 9 · Record | Has the maintenance history been updated? |
Grouped by fixture maintenance discipline — click any topic to expand its check points and acceptance condition.
Record: significant defects against the fixture for corrective action.
Method: compatible with the fixture material and manufacturer requirements.
Classify as: Cosmetic → Repairable → Performance-affecting → Structural.
Torque: tighten using approved torque requirements — avoid uncontrolled over-tightening, which can damage fixture components or mounting arrangements.
Suitability: replacement hardware matched to the fixture and installation environment.
Objective: confirm the fixture's intended frangible arrangement remains intact.
Use: the correct approved frangible component only.
Re-check: alignment after any activity that could disturb the fixture.
Impact: incorrect elevation can affect both operational performance and mechanical protection.
After cleaning: inspect the lens.
Handle: carefully — prisms are optical-critical components.
Sequence: Inspect → Clean → Secure → Verify optical condition → Functional test.
Critical: correct installation — prism orientation can affect optical performance.
Formal verification: use the applicable approved photometric test method where required, rather than relying on visual observation alone.
After installation: functional test → illumination verification → record replacement.
After replacement: secure module, restore sealing, verify illumination, verify optical orientation where applicable.
Use: correct approved components only.
Note: a connector defect can present as a fixture failure.
Do not: simply remove water — correct the underlying condition.
Threshold: minor surface corrosion may be treated per approved procedures; advanced or structural corrosion triggers a repair/replacement decision.
Otherwise: moisture may return and produce repeated failures.
Formal verification: photometric verification performed where required by the applicable inspection/testing program.
Division 06 does not replace the maintenance-management divisions — it is the fixture-level technical reference they invoke.
Routine fixture cleaning, tightening, alignment and inspection.
Failed fixture / component repair and replacement.
Fixture failure-rate and performance trending.
Fixture condition assessment and maintenance decision.
Emergency fixture restoration after critical failure or damage.
Quick answers about lighting fixture maintenance, based on the topics in this division.
It is the dedicated division for the physical AGL light fixture itself, covering every fixture type regardless of where it sits on the airfield. It does not replace the maintenance-management divisions; it is the fixture-level technical reference they invoke.
Division 06 (Lighting Fixture Maintenance) contains 35 topics in five groups: Group A Mechanical Maintenance (10 topics), Group B Optical Maintenance (7 topics), Group C Electrical Maintenance (8 topics), Group D Environmental Protection (6 topics) and Group E Restoration (4 topics).
No. Its mechanical, optical, electrical, environmental and functional condition, including alignment, must all remain acceptable together.
Runway, taxiway, centreline, threshold and end, touchdown-zone, runway guard-light, approach-light and stop-bar fixtures, and other AGL light fixtures. The same mechanical, optical, electrical and environmental procedures apply wherever the fixture is installed.
Seven steps: Inspect, Clean, Repair/Replace, Align, Seal/Protect, Test and Record.
Technicians work through a decision logic: what is physically wrong, is contamination causing the condition, is the component damaged or deteriorated, can it be restored, is the fixture correctly positioned, is it protected against environmental ingress, does it function correctly, is the final condition acceptable, and has the maintenance history been updated.
Division 01 uses it for routine fixture cleaning, tightening, alignment and inspection; Division 02 for failed fixture and component repair; Division 03 for fixture failure-rate and performance trending; Division 04 for fixture condition assessment and maintenance decisions; and Division 05 for emergency fixture restoration after critical failure or damage.
Lighting fixture maintenance is more than cleaning a lens and checking a bulb.
Build the technical knowledge to understand photometric performance, optical degradation, mounting integrity, and how fixture condition affects the wider AGL system.
Maintain the fixture. Protect the photometrics. Understand the system.
Please read before relying on any content on this page or on any record downloaded from it.